M1030-E Series Tonnage Monitor Part Numbers

M1030 Press Load Monitor/Peak Tonnage or Signature Analysis System
1. M1030 PLS
1.1 1030 PLM:
SAC-M1030-PLMx		Programmable Load (Peak Tonnage) Monitor (Resolver is not required)
Where x = Number of Inputs
2:		Two channel
4:		Four channel
8:		Eight channel (consult factory for availability)
1.2 M1030 Signature Analysis:
SAC-M1030-RD4		Base unit for tonnage at angle for up to 4 sensors. Relays are included for Q, D, and P outputs.
SAC-M1030-R08		Base unit for tonnage at angle for up to 8 sensors. Relays are included for Q, D, and P outputs.
SAC-M1030-GR4		Base unit for 4 sensors with Graphic Communication Link for On-Line Monitoring and Profile Management
SAC-M1030-GR8		Base unit for 8 sensor with Graphic Communication Link for On-Line Monitoring and Profile Management.
SAC-M1030-GM04		Base unit for 4 sensors with Graphic Communication Link for On-Line and Critical Curve Monitoring.
SAC-M1030-GM08		Base unit for 8 sensors with Graphic communication Link for On-Line and Critical curve Monitoring.
Slave Unit	S:	For M1030 Signature Series, change the “A” in SAC (in above parts) to “S”
2. Sensors, Amplifiers, Cables and Installation Kits
2.1 Select strain gauge or amplifiers needed:
SAC-M1030-SEND		1 strain gauge sensor with amplifier assembly, box and cover, 2 torque pads and 4 mounting screws ¼ - 28 x ¾” socket head cap
SAC-M1030-SENW		1 strain gauge sensor with amplifier assembly, box cover, 2 weld pads, 2 torque pads, and 4 mounting screws (1/4 – 28 x ¾” socket head cap)
ASY-M1030-AMPD		Retro-fit amplifier assembly includes amplifier assembly for die sensors, screw terminals for sensor connection
ASY-M1030-AMP		Retro-fit amplifier assembly includes Amplifier assembly mounted on standard cover, screw terminals for sensor connection
ASY-M1030-STG		Strain Gauge Element, with connector for Autotech’s Amplifier Assembly
2.2 Select Installation kit needed:
KIT-M1030-INSTL		Installation kit includes Gauge block and temporary mounting screw, #8 HS drill bit, ¼ - 28 NF tap, and 4 temporary weld pad mounting screws
KIT-M1030-TORQ		Torque Pads (2), and mounting screws (4) ¼ x 28 x ¾”
KIT-M1030-WELD		Weld Pads (2), and temporary screws (4) ¼ - 28 x 1”
CBL-10T22-Cxxx		Recommended shielded cable for the sensor wiring and Graphic Communication Link. (Where xxx is length in ft.) Length ordered must be 010, 020, or 050 feet and increments of 50 ft.
3. Serial Communication Software, Cables and Communication Adapter, IBM Compatible
3.1 Serial Communication Software:
SAC-M1030-SOFT		“PC” software used in conjunction with the Graphic Communication Link
SAC-M1030-SFTGM		“PC” software used in conjunction with the Graphic Communication Link and Critical Curve
3.2 Serial Communication Adaptor:
SAC-RS232-485T		Adaptor for RS232 to RS485 required if an IBM compatible PC is used instead of T60
3.3 Serial Communication Cables:
CBL-232MF-9Pxxx		Serial Cable for connecting PC to RS232 port of RS232-485 adaptor (where xxx is length in ft.)
CBL-09S22-DAxxx		9-Conductor cable with overall foil shield and DSub connector at one end. Used to connect RS 485 port on adapter to M1030 serial port (where xxx is length in ft.)
4. Position Transducers
The M1030 Press Load Monitor/Signature Analysis System requires a single turn resolver as an input device, such as Autotech’s RL100, RL101, RL500, RL501, E1R, E7R, E8R or E9R series of resolvers. Please see position transducer section for ordering information on these resolvers and appropriate accessories.

Note: For Part Numbers and Price of individual components, cables & accessories, strain-gauge sensors & amplifiers, and other product variations such as additional PLM outputs, call the factory.